UK

Please select a language / region

 

Pultruded profiles for spar caps

Spar caps for wind turbines Röchling

Consistently high quality: our pultruded profiles for spar caps offer high mechanical properties, lower the manufacturing risk and shorten the mould occupancy time.

Spar caps for wind turbines different reinforcements

Customised for your application: our pultruded profiles for wind turbine spar caps come with different fibre reinforcements, resin systems and cross-sections

Spar caps for wind turbines with peel ply and without peel ply

On demand: We also offer profiles for spar caps with peel ply (left) and without peel ply on request

Or: How can you strengthen your rotor blades for wind turbines?

Together with the ribs, the two spar caps in the rotor blade shells are, you might say, the skeleton of each and every rotor blade of a wind turbine, and they must be able with withstand very high loads for the entire life of the turbine. That makes it essential to deliver high component quality and to ensure that the best possible properties of the mix of fibres and matrix are achieved.

We offer you pultruded profiles for spar caps with

  • different fibre reinforcements

  • resin matrices

  • and cross-sections

Our profiles are manufactured in the pultrusion process. The continuous process enables us to manufacture almost endless profiles of a consistently high quality. The tensile forces prevailing during pultrusion make the reinforcing fibres very straight in orientation, thereby heavily reducing occurrence of the fibre undulations that occur frequently in other manufacturing processes.

Material - profiles for spar caps:

Fibre reinforcements:

  • Glass fibre reinforcement
  • Carbon fibre reinforcement

Resin systems:

  • Epoxy resin
  • Vinyl ester resin
  • Polyurethane resin
  • UV-curing resins, depending on the profile cross-section

Cross-sections:

With thermal pultrusion:

  • Reinforcement with glass or carbon fibres possible
  • Various cross-sections: width up to 200 mm, wall thickness 1.2 to 5 mm

UV-curing pultrusion:

  • Only glass fibre reinforcement possible
  • Wall thickness approx. 0.75 to 2.5 mm

Peel ply
Our profiles for spar caps for wind turbines are also available with a peel ply on request, removing the need to roughen the surface, e.g. by sand blasting, before fitting the profiles.

Your advantages:

Our pultruded profiles are pre-cured and quality-tested insertable components with clearly defined, very high mechanical properties. That allows excessive material defects such as fibre undulations or air bubbles to be eliminated from these profiles right from the start, enabling error rates, manufacturing risk and repair requirements for the spar caps to be drastically reduced. The mould occupancy time for the rotor blade shells is also much shorter using this method than for spar caps produced in the traditional manner.

Summary:
High mechanical properties:

  • Advantages of the pultrusion process compared with resin infusion
  • Higher volumetric fibre content
  • Better fibre orientation

Reduced manufacturing risk: 

  • Pultrudate is tested in advance according to defined criteria - only flawless material is used in the rotor blade
  • Material defects that can arise in the spar cap area when rotor blades are manufactured in the traditional manner can thus be eliminated almost entirely

Shorter mould occupancy times

Technical data - Profiles for spar caps

Test methodDimensional unitEP-CFK
(D343)
VE-CFK
(D745)
VEGZ-LP
(D677)
EPGZ-UV
(UV cured)
Fibre typesCarbon (50K)Carbon (24K)GlassGlass
Resin typesEPVEVEEP-based
DensityISO 1183g/cm31.61.5 - 1.62.12.0
Volumetric fibre content%66656564
Tensile strength (II)ISO 527MPa20002400600 - 8001500
Tensile modulus of elasticity (II)ISO 527GPa15016545-6045-50
Flexural strength (II) ISO 178MPa-1200700-1000890-1020
Flexural modulus of elasticity (II)ISO 178GPa-120-14050-5535-45
Pressure resistance (II)      ISO 14126MPa1000-450-800-
Compression modulus of elasticity (II)  ISO 14126GPa145-50-55-

 (II) = relative to the profile longitudinal direction

The figures given above are mean values obtained through continuous statistical checks and tests. They are provided as an indicator of quality only and do not establish any warranty unless and until expressly agreed in a purchase contract.

Find other Röchling News

Visit the Röchling Group Newsroom to get the latest news and an insight into the latest developments in our company.

Röchling Newsroom
 
Search

Refine Results

Contact

Share

Print to PDF

Newsletter Registration

Select Website

Roechling_Industrial_Banner.jpg
Plastics for technical Applications

Industrial